Find out more about our advertising opportunities. Advertise Advertising on is well-targeted, has unique benefits, and is highly successful. Looking for something lighter? Read our funny complaints to see people who found humor in a bad situation. Vehicle Problems Find out what cars to avoid, view the latest problem trends, or keep up-to-date with the most recently reported problems. Contact us with any comments or concerns. SPONSORED Outside Door Handles Front Rear Set of 4 For 03-08 Pontiac Vibe Toyota Corolla (Fits: Pontiac Vibe) 14.35 Free shipping or Best Offer 44 sold SPONSORED New Door Handles Front Rear Set of 4 For 03-08 Pontiac Vibe Toyota Corolla (Fits: Pontiac Vibe) 14. Car Problem Resources Around the Site Information Find out more about us in the press or read stories from drivers who praise our work.The complaints are organized into groups with data published by vehicle, vehicle component, and specific problem. Remove the sliding door exterior ® is an online automotive complaint resource that uses graphs to show automotive defect patterns, based on complaint data submitted by visitors to the site.For additional information, refer to Latch Remote Control-Sliding Door. Remove the sliding door latch remote control.Remove the sliding door latch remote control. NOTE: If necessary, transfer parts to the new sliding door latch remote control. Remove the 4 sliding door front latch bolts.Disconnect the sliding door rear latch cable from the latch remote control.Remove the sliding door rear latch cable adjusting bracket from the latch remote control.Disconnect the sliding door rear latch cable.NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.If equipped, disconnect the sliding door power door lock actuator electrical connector.For additional information, refer to Section 501-05. Remove the rear sliding door trim panel.Remove the sliding door trim panel finish panel.If you were in detroit area, I wold help you. Quest & mecrury villager are the same vehicle made at the same assembly plant. remove the ext door handle (bottom edge out first)įirst you van order parts at discount from. using access area now available remove rod from ext door handle from inside door areaĢ0. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)ġ8. remove the 3 screws and panel for access to door handle.ġ7. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screwsġ6. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)ġ5. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)ġ4. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.ġ3. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed inġ2. remove 3 phillips/hex screws along the bottom inside of door panelġ1. remove the 2 phillips screws w/ captive washersġ0. May also require small screwdriver approx 1/8" in to complete pop offĩ. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. remove large phillips screw under sw panelĨ. slide switch panel toward rear to allow removalħ. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)Ħ. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove coverĥ. /rebates/2fexterior-door-handle2fpontiac2fvibe&252fexterior-door-handle252fpontiac252fvibe26tc3dbing-&idcarparts&namecarparts&ra6. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)Ĥ. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)ģ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |